6EP7133-6AB00-0BN0 PS 24VDC/5A (120/230VAC) SIMATIC ET 200SP

Liên hệ

SIMATIC ET 200SP PS 24V/5A Stabilized power supply Input: 120/230 V AC Output: 24 V DC/5 A.

Tải về datasheet (pdf): Tại đây!

6EP7133-6AB00-0BN0 là bộ cung cấp nguồn ổn định cho các thiết bị SIMATIC ET 200SP được hãng SIEMENS sản xuất & phát triển với thương hiệu SIMATIC thuộc dòng ET 200. 6EP7133-6AB00-0BN0 được MESIDAS GROUP phát triển và phân phối rộng rãi trên thị trường Việt Nam. Nếu quý khách hàng đang có nhu cầu cần tư vấn, báo giá hay mua 6EP7133-6AB00-0BN0 thì hãy liên hệ MESIDAS.COM để được hỗ trợ một cách tận tâm, nhanh chóng và hiệu quả nhé.

6EP7133-6AB00-0BN0 PS 24VDC/5A (120/230VAC) SIMATIC ET 200SP

Bảng tóm tắt thông số kỹ thuật 6EP7133-6AB00-0BN0

SIMATIC ET 200SP PS 24V/5A Stabilized power supply Input: 120/230 V AC Output: 24 V DC/5 A

Mã sản phẩm 6EP7133-6AB00-0BN0
Dòng sản phẩm SIMATIC ET 200SP PS
Hãng sản xuất SIEMENS
Nguồn đầu vào 120/230 V AC
Nguồn đầu ra 24 V DC/5 A
Kích thước (RxCxS) 160 x 117 x 74 mm
Trọng lượng 500 g

Bảng chi tiết thông số kỹ thuật 6EP7133-6AB00-0BN0

Article number 6EP7133-6AB00-0BN0
Product SIMATIC ET 200SP PS
Power supply, type 24 V/5 A
Input
Input 1-phase AC
● Note Automatic range selection
supply voltage
● 1 at AC rated value 120 V
● 2 at AC rated value 230 V
input voltage
● 1 at AC 85 … 132 V
● 2 at AC 170 … 264 V
Wide-range input No
Overvoltage resistance 2.3 × Vin rated, 1.3 ms
Mains buffering at Vin = 93/187 V
Mains buffering at Iout rated, min. 20 ms; at Vin = 93/187 V
Rated line frequency 1 50 Hz
Rated line frequency 2 60 Hz
Rated line range 47 … 63 Hz
input current
● at rated input voltage 120 V 2.16 A
● at rated input voltage 230 V 1.22 A
Switch-on current limiting (+25 °C), max. 45 A
I²t, max. 3.15 A²·s
Built-in incoming fuse T 3,15 A/250 V (not accessible)
Protection in the mains power input (IEC 898) recommended LS switch: B/C 6 A/3 A
Output
Output Controlled, isolated DC voltage
Rated voltage Vout DC 24 V
● output voltage at output 1 at DC rated value 24 V
Total tolerance, static ± 3 %
Static mains compensation, approx. 0.1 %
Static load balancing, approx. 1 %
Residual ripple peak-peak, max. 150 mV
Residual ripple peak-peak, typ. 50 mV
Spikes peak-peak, max. (bandwidth: 20 MHz) 240 mV
Spikes peak-peak, typ. (bandwidth: 20 MHz) 150 mV
Adjustment range 22.8 … 28 V
product function output voltage adjustable Yes
Output voltage setting via potentiometer
Status display Green LED for 24 V OK
Signaling Relay contact (NO contact, rating 60 V DC/ 0.3 A) for “24 V OK”
On/off behavior Overshoot of Vout < 3 %
Startup delay, max. 0.3 s
Voltage rise, typ. 30 ms
Rated current value Iout rated 5 A
Current range 0 … 6 A
● Note 5 A up to +60°C; +60 … +70 °C: Derating 3%/K
supplied active power typical 120 W
short-term overload current
● on short-circuiting during the start-up typical 15 A
● at short-circuit during operation typical 15 A
duration of overloading capability for excess current
● on short-circuiting during the start-up 800 ms
● at short-circuit during operation 800 ms
Parallel switching for enhanced performance Yes
Numbers of parallel switchable units for enhanced performance 2
Efficiency
Efficiency at Vout rated, Iout rated, approx. 88 %
Power loss at Vout rated, Iout rated, approx. 17 W
power loss [W] during no-load operation maximum 2.7 W
Closed-loop control
Dynamic mains compensation (Vin rated ±15 %), max. 0.3 %
Dynamic load smoothing (Iout: 10/90/10 %), Uout ± typ. 3 %
Load step setting time 10 to 90%, typ. 1 ms
Load step setting time 90 to 10%, typ. 1 ms
Protection and monitoring
Output overvoltage protection protection against overvoltage in case of internal fault Vout < 31.8 V
Current limitation 7 … 7.5 A
property of the output short-circuit proof Yes
Short-circuit protection Constant current characteristic
enduring short circuit current RMS value
● typical 7 A
overcurrent overload capability in normal operation overload capability 150 % Iout rated up to 5 s/min
Overload/short-circuit indicator
Safety
Primary/secondary isolation Yes
galvanic isolation Safety extra-low output voltage Uout acc. to EN 60950-1 and EN 50178
Protection class Class I
leakage current
● maximum 3.5 mA
● typical 1 mA
Degree of protection (EN 60529) IP20
Approvals
CE mark Yes
UL/cUL (CSA) approval cULus-Listed (UL61010-2-201, CSA C22.2 No.142), cCSAus (CSA C22.2 No. 60950-1, UL 60950-1)
certificate of suitability NEC Class 2 No
CB approval Yes
certificate of suitability EAC approval Yes
Marine approval BV, DNV GL
EMC
Emitted interference EN 61000-6-3 Class B
Supply harmonics limitation EN 61000-3-2
Noise immunity EN 61000-6-2
environmental conditions
ambient temperature
● during operation -30 … +70 °C
— Note with natural convection
● during transport -40 … +85 °C
● during storage -40 … +85 °C
Humidity class according to EN 60721 Climate class 3K3, 5 … 95% no condensation
Mechanics
Connection technology Push-in terminals
Connections
● Supply input L, N, PE: 1 push-in terminal each for 0.2 … 2.5 mm² single-core/finely stranded
● Output +, -: 2 push-in terminals each for 0.2 … 2.5 mm²
● Auxiliary Signaling contact: 2 push-in terminals for 0.2 … 2.5 mm²
● signaling contact 2 push-in terminals for 0.2 … 2.5 mm²
product function
● removable terminal at input Yes
● removable terminal at output Yes
width of the enclosure 160 mm
height of the enclosure 117 mm
depth of the enclosure 74 mm
required spacing
● top 50 mm
● bottom 50 mm
● left 0 mm
● right 0 mm
Weight, approx. 0.5 kg
product feature of the enclosure housing can be lined up Yes
Installation Snaps onto DIN rail EN 60715 35×7.5/15
electrical accessories Redundancy module, buffer module, selectivity module, DC UPS
MTBF at 40 °C 1 598 441 h
other information Specifications at rated input voltage and ambient temperature +25 °C (unless otherwise specified)

Phân phối & báo giá 6EP7133-6AB00-0BN0

Nếu quý khách hàng đang có nhu cầu cần tư vấn, báo giá hay mua 6EP7133-6AB00-0BN0 thì hãy liên hệ MESIDAS.COM để được hỗ trợ một cách tận tâm, nhanh chóng và hiệu quả nhé.

5/5 - (1 bình chọn)
Nhận thông báo qua Email
Nhận thông báo cho
guest

Mới nhất
Cũ nhất
Inline Feedbacks
View all comments
0
Would love your thoughts, please comment.x